Best NACE-CIP2-001 Exam Dumps for the Preparation of Latest Exam Questions
NACE-CIP2-001 Actual Questions 100% Same Braindumps with Actual Exam!
NEW QUESTION # 44
NACE International Standards are developed by:
- A. Regional mandates
- B. Standard committees
- C. Government mandates
- D. International mandates
Answer: B
NEW QUESTION # 45
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. epoxies.
- B. urethanes.
- C. inorganic zincs.
- D. powder coatings.
Answer: C
NEW QUESTION # 46
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Gel stage
- B. Wetting stage
- C. Cure stage
- D. Flow stage
Answer: D
NEW QUESTION # 47
The HATE adhesion tester uses
- A. a special tape to apply pressure to the test dolly.
- B. a hydraulic piston to apply pressure to the test dolly.
- C. compressed air to apply pressure to the test dolly.
- D. mechanical means only to apply pressure to the test dolly.
Answer: B
NEW QUESTION # 48
Inspection and Test Plans are provided to:
- A. So the Inspector doesn't have to read the entire specification
- B. To supersede the requirements of the product data sheets
- C. So the contractor has a single document to reference
- D. Outline the inspection steps, sequencing and pass/fail criteria
Answer: D
NEW QUESTION # 49
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise your QC Manager to change the ITP to the use of the salt smart meter
- B. Redo the pre-cleaning based on the other inspectors results
- C. Advise the other inspector he is using an incorrect method
- D. Review the specification with the other inspector to see what method was specified
Answer: D
NEW QUESTION # 50
Individuals conducting Coating Surveys should:
- A. Always be NACE Level 3 Certified Inspectors
- B. Always be NACE or SSPC Protective coating Specialists
- C. Always be trained and experienced Coating Industry
- D. Always be experienced Specification Writers
Answer: C
NEW QUESTION # 51
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. No difference from any other coating
- B. A very high reading
- C. A very low reading
- D. Cold flow or creep
Answer: D
NEW QUESTION # 52
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Make sure they are the center of attention in all site meetings
- B. Implement immediate to get them motivated
- C. Challenge their value to the team and try to get them out of their comfort zone
- D. Give them as much advance notice as possible about upcoming changes
Answer: D
NEW QUESTION # 53
A single component water borne acrylic coating cures by:
- A. Oxidation
- B. Solvent Evaporation
- C. Coalescence
- D. Co-Reaction
Answer: C
NEW QUESTION # 54
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Coal Tar Enamel
- B. Concrete
- C. Heat-shrink sleeves
- D. Liquid epoxies
Answer: D
NEW QUESTION # 55
When observing fabrication defects the NACE Inspector should:
- A. Require they be corrected prior to coating
- B. Consult the specification to determine how they should be treated
- C. Write an NCR and call the fabricator
- D. Stop the job immediately
Answer: B
NEW QUESTION # 56
External coatings applied to buried pipelines are generally tested for:
- A. Cathodic disbondment
- B. Gloss level
- C. Chalking resistance
- D. Solvent resistance
Answer: A
NEW QUESTION # 57
You can use magnifiers to examine all of the following EXCEPT
- A. Blisters
- B. Surface profile
- C. Mill scale
- D. Surface cleanliness
Answer: D
NEW QUESTION # 58
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Review the standard with the Contractor and re-inspect the floor
- C. Shut the job down
- D. Request that the Contractor re-blast the floor
Answer: B
NEW QUESTION # 59
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Meet with the prospective employer to scope of your role
- B. Accept assignment without hesitation
- C. Advise the prospective employer that you cannot accept the position
- D. Review the NACE Attestation prior to making a decision
Answer: D
NEW QUESTION # 60
Corrosion is the reverse process of
- A. hot dipping.
- B. flaking.
- C. steel manufacturing.
- D. galvanic deterioration.
Answer: C
NEW QUESTION # 61
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of chemical exposure
- B. a), b), and c)
- C. Risk of skin
- D. Risk of acid or caustic splashes
Answer: B
NEW QUESTION # 62
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by SP 3
- B. SP 1 followed by caustic etching
- C. SP 1 followed by acid etching
- D. SP 1 followed by SP 2
Answer: D
NEW QUESTION # 63
The Concrete Repair Institute's comparators can be used to assess:
- A. Surface profile prior to coating
- B. Surface cleanliness prior to coating
- C. Compressive and tensile strength prior to coating
- D. Contamination levels prior to coating
Answer: A
NEW QUESTION # 64
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Scarifiers
- B. Water Jetting Equipment
- C. Abrasive Blasting Equipment
- D. Power Tools
Answer: B
NEW QUESTION # 65
When conducting inspections the Inspector should follow which standards:
- A. NACE and SSPC standards in North America
- B. Australian standards in Australia
- C. The specified standards
- D. ISO standards in Europe and Asia
Answer: C
NEW QUESTION # 66
Coating application to concrete substrates is:
- A. Not required as Concrete is inorganic
- B. The same as coating steel
- C. More challenging than coating steel
- D. Less challenging, than coating steel
Answer: C
NEW QUESTION # 67
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. False
- B. True
Answer: A
NEW QUESTION # 68
......
NACE-CIP2-001 Study Material, Preparation Guide and PDF Download: https://actualtests.testbraindump.com/NACE-CIP2-001-exam-prep.html
